One for redirects and another one - the actual application.įor your actual application in IIS assign binding address: įor redirection application assign bindings for addresses:, and Īnd enable HTTP redirect to with status code: Permanent (301).
So our goal is to configure IIS/TMG to redirect the following addresses with response code 301:įirst step - configuring IIS applications.įor this to work we will need two IIS applications. There are few ways you can do that via TMG, but it will result in 302 redirects which you want to avoid and instead use 301 response code for redirection (so I've been told by SEO guys).
įor this we will need to setup some redirection rules. These keys are only for this scenario & are published publicly on the Microsoft Website. I’m already trying to fix this on the image configuration level by completely uninstalling all office programs and reinstalling them clean to make sure the built in repair mechanism can open if it happens again.You need to publish a new secure website and to avoid situations where users can't access your site because they do not know the difference between http vs. The following product keys can be entered into the product key field in your office application when your computer is joined to a Active Directory with a valid working KMS server. But when it happened yesterday the computers were being imaged individually. The first time this happened I was unicast imaging 2 other computers that both worked fine. Could a weird network error cause this, like a part of the image doesn’t make it to the computer?maybe the ethernet cables are just that old? The first time this happened I had discovered the machine was plugging into the network with a cat 5 cable and we just upgraded the switch to a gigabit switch, so I swapped it out with a newer cat 5e so it could image faster and that’s when I discovered after reimaging the problem was fixed. The Office 2010 KMS host will activate any Office 2010 suites, applications, in addition to Project 2010 and Visio 2010 ' So : Q. So why would sometimes office work perfectly fine and other times not so much. The quickest way to fix this is to just re-image it and then it works. In the event viewer there was some error about not being able to register to proof of purchase or something like that. I tried to look at the cmid (client machine id) and it says it doesn’t exist.
The only thing that should be noted is that in Windows Server 2003 the support of the KMS-server for Office 2013 is now absent. In general, KMS-activation of Office 2013 doesn’t differ from the activation of Office 2010. Tried a MAK key too that also is claimed to be invalid, but I know that both keys are valid. The same server can simultaneously act as an activation KMS server for different Windows and Office editions. I tried adding it in the command line with and without dashes to no avail.
I tried to use ossp.vbs to manually install the GVLK kms client key and it says the key is invalid. I played with the office ossp.vbs activation tool to manually add the kms host and port and attempted to activate but it keeps claiming no key is installed.
If I go to the kms server and look at VAMT, I can add the host and update the license status and the kms server successfully activated windows 10 no problem but it doesn’t even see Office 14 (2010) as an activated device. Do not attempt to download KMS Activator Ultimate V1.0, KMS Activator Ultimate V1.8, Download instead Windows KMS Activator Ultimate v4.8 2021 which is the latest version of KMS Activator updated this 05 August 2019 to crack Windows (10, 8, 8.1, 7, ) and MS office (2019, 2016, 2010, 2010, etc) for free. It pops up and then after a second or two it pops up an error about office activation failing and a repair attempt failed (the office 2010 setup splash screen pops up and disappears right before that) But then I try to open any Microsoft Office 2010 program. I image the computer and all seems to go well.
It’s only happened 3 times out of the last 13 computers imaged in the last few weeks, but 2 of those were yesterday.
So I have been having a really weird problem recently. TL DR - After imaging office 2010 fails to activate and can’t be activated, is fixed by re-imaging.